London Marble Show and some Marble FAQs

My View @ London Marble Show

I’m so pleased to have been a part of the very first London Marble Show.

Myself and Paul Harris from Teign Valley Glass travelled up to London Glassblowing Studio to demonstrate our different techniques of marble making to the public.

Visitors included marble collectors, glass art collectors, local people and lots of children too

Bermondsey village hall, just a few minutes walk away held marble collectors, enthusiasts and sellers, and a team from the House of Marbles showcasing a selection of items from the luxury solitaire board filled with beautiful large Teign Valley Glass Handmade marbles, to the sillier items like the flying cowpat and rubber slugs

I spent my day with a view (between people!) of the Glass Gallery space of London Glassblowing, which as you can see contained a lot of colour (and a lot of Elliott Walker!)

 

Some of the top questions I was asked, which I’ll answer again here for anyone else curious

 

Is this how all marbles are made?

No! Not even all my marbles are made the same way.
I make my marbles with a blowtorch, there are also hotshop marbles which are made by Glassblowers like Paul, and of course machine made marbles which are entirely different!
In Flamework, loosely speaking, you can make them a sphere and then decorate it, or you can make the decoration and then shape it into a sphere.
I do both! My foiled designs and the textured flowers start with a sphere which I’ll add further layers to, but always staying fairly round throughout the process.

The carnival stripes and the flowers start in a more inside out fashion and don’t get made round until nearer the end of the process.

 

How did you get into this?


When I was little my Mum made jewellery, so I would play with beads and thread and wire, and make my own jewellery too. When I was maybe 15 or 16, we went on a jewellery making evening class as we wanted to use some equipment they had, but which we didn’t. Someone else on the course had a glass kiln and was doing glass fusing…can we have a go?

So we got into glass fusing, later we found a weekend course lampwork bead making, and then I did my degree in Applied arts: Ceramics, Metals and Glass where I thought I wold mostly focus on jewellery…instead I spent most of my time behind a torch!

 

How long have you been doing this?


I say its 18 years, though its actually 19 now! But I started with beads and small sculptures, and started to include marbles over 10 years ago.

 

How do you get the flowers in?


They start from the inside out, I start by forming what will be the lens of the marble, and draw the flower on from the back. Then with a little glass magic, I slowly slowly stretch the clear around the flower and it ‘blooms’ up into the clear lens. Once its fully inside the clear, I put the decoration and the colour on the back. I switch handles (called punties) from one end to the other so I can access whichever side of the marble I need to get at. Finally it is made round and knocked off, then I’ll polish the tiny spot that’s left in the flame, and its time for a very slow cool down.

 

How do you make it round?


A combination of heat, gravity and finishing with a circular graphite mould. A paddle with a hole in it essentially. I only need the inner edge of the circle, not a full hemisphere like you might think.

 

How long does it take to make a marble?


That depends on the marble! Some of the designs take well over an hour of concentration and focussed work, once you start, you cannot put it down, its finish it or bin it (and I don’t like wasting glass!).
Additionally most of my designs require at least a little preparation, usually in the form of pulling stringers or thin rods of different coloured glass to go into the designs. Some of the designs require up to 16 different colours

 

Do they need annealing?


Well clearly some of you know your glass!
Yes, ideally they would be annealed, but for my demo, they were put into cooling bubbles to insulate them as much as possible as I didn’t have a kiln with me to put them in. 
What is annealing? this is the process of cooling the glass down very slowly in a digitally controlled kiln, to even out the temperature in order to alleviate stresses that build up in the glass while its being made.

If I didn’t cool them slowly, since glass (as do most things) expands when its hot,
the outside that is in contact with cooler air will cool quicker than the inside of the glass that is not, and this uneven cooling can break the glass apart. Sometimes quite violently!

Turquoise and Chocolate Marble
Ink Purple Rose Marble
Blue Silver Foiled Marble

Did you miss out on getting one of my marbles?

You can find them in my Etsy shop, or right here on my website

Lastly a big thankyou to Monika Ma, and London Glassblowing for organising and hosting this event

This site uses cookies to offer you a better browsing experience. By browsing this website, you agree to our use of cookies.